1Sid
regular
Reged: 09/10/2007
Posts: 43
|
|
Would be grateful for recommendations for following works on my steel cruiser:
full service of diesel engine (perkins) air filters, generator etc
and separately for later in the year -
hull blasting and repaint and anti foul
and any guides to fair prices to expect (hourly rates etc.)
Many thanks
|
martin1001
regular
Reged: 08/11/2006
Posts: 435
|
|
this is worrying
If you had asked how to service the engine yourself you would have 25 answers by now ... but finding a good marine engineer seems to be a question with a more elusive answer.
For a marine engineer I think you can expect about £50+ an hour. The standard charges I have seen for servicing (eg £500) engines are ridiculous when you consider what little there is to do on a diesel engine.
As far as anti-fouling some boatywards do a deal when they are slack. If you mean a pressure wash and anti foul most will do that. If you mean 'blasting' to take all old paint off then I am not sure where that can be done. I think Shepperton Marina do that (or maybe they bring in an outside agency - I'm not sure)
|
martin1001
regular
Reged: 08/11/2006
Posts: 435
|
|
oh yes ... and make sure you are there when the boat is craned out of/into the water.
It is rare, but not unknown for boats to be dropped .. like one great big bang I heard just a couple of weeks back.
|
Brayman
regular
Reged: 27/11/2006
Posts: 1223
Loc: Bucks
|
|
We had ours shotblasted at Harleyford a few years back - about £4k IIRC. Fortunately I didn't have to pay.
--------------------
How come I am over the hill but I never made it to the top?
http://www.braycruiserclub.co.uk
|
1Sid
regular
Reged: 09/10/2007
Posts: 43
|
|
Thanks for the advice. About what I thought. Unfortunately the hull does need shot blasting have tried one yard left messages, e-mailed but can I get a retunred call ...... seems they just don't want the work. On the engine front, I did manage petrol engines about thirty years ago, but servicing a diesel engine for what would be first time is unfortunately just too daunting. Was the terrific crash anywhere near that I should worry about (not) using? Thought I would watch the crane out and stand with all fingers crossed!
|
Chris_d
regular
Reged: 15/06/2001
Posts: 1529
Loc: Oxfordshire
|
|
I'd struggle to think of a marine engineer let alone recommend one, however Lindon Lewis Marine at Shepperton's advertised rates always look reasonable, i'd give them a go. But to be honest servicing a diesel is easy, just change the oil and fuel filters, even the bleeding is easy I just fill the filter with fuel and start the engine, never had to bleed one yet.
|
temptress
regular
Reged: 15/08/2002
Posts: 672
Loc: Portsmouth, UK
|
|
I live in Molesey and have had work donw by Lindon Lewis Marine at Shepperton although they can be expensive when compared to prices charged on the coast (Brighton/Solent)
--------------------
Temptress of Down
Southsea Marina
Portsmouth
Hants
UK
Check out our YotBlog
|
BlueMoon1
regular
Reged: 25/10/2006
Posts: 10
Loc: Live Merton Park; moor at Shep...
|
|
I'm going to stick my neck out and recommend Bridge Marine, just by Walton Bridge, Try: www.bridgemarine.co.uk
Their chief engineer has a steel boat and they have two diesel engineers as well.
Alan
|
1Sid
regular
Reged: 09/10/2007
Posts: 43
|
|
Hi Alan
Many thanks for "sticking your neck out much appreciated. I will drop in and see them as I am doing with Linden Lewis.
Many thanks
|
Previous
Index
Next
Threaded
Edit
Reply
Quote
