hughiain
regular
Reged: 13/07/2001
Posts: 96
Loc: kent
|
|
My boatyard has advised me to apply 1 coat at the start and end of each day to make 6 coats in all over 3 dry days. They say that each coat of epoxy must be applied when the previous coat is still tacky.
With Gelshield will there be any problem if one coat dries out before a further coat is applied? I am also told by the boatyard to apply the initial antifoul when the epoxy is still 'tacky'.
The surveyor has checked the hull of my boat and confirmed that it is between 4 and 5 and well dry enough for epoxying.!
|
VicS
regular
Reged: 13/07/2002
Posts: 8369
Loc: Home: Kent. Boat: Chichester
|
|
I suggest you refer to International's data sheet and follow that rather than anything else Here
They say 5 coats with between 5 hours and 6 months between coats at 15C (If the maximum time is exceed then sand it with 180 or 220 grade paper) At 15C it is touch dry in 2hours. That does not seem to be a question of applying the next coat while the previous is still tacky!
Times are also given for applying antifouling paints. 5 hours to 9 hours as far as I can see.
But read it all for yourself.
--------------------
Old Chemists never die, they just fail to react
Edited by VicS (14/05/2008 20:56)
|
graham
regular
Reged: 16/05/2001
Posts: 5852
Loc: k the booze locker here comes ...
|
|
Use alternate colours (grey and green) for each succesive coat so you can see the bits you missed. Foam rollers are good for putting it on but dont last long in the epoxy so have plenty of spare roller heads.
--------------------
http://banjocoronado25.blogspot.com/
All Hardwood used in Banjos restoration comes from sustainable sources. Usually the Boat Club Skip :-)
|
Leighb
regular
Reged: 08/08/2007
Posts: 329
Loc: Suffolk
|
|
There is a very clear article on the Gelshield process in PBO May 08.
Goes through the whole process from start to finish with pictures. It says you can apply 2 coats a day, but also that you can leave it up to 6 months between coats without any need to re-key the surface.
The only exception is that the antifouling must go on the same day as the last coat of Gelshield.
Worth reading if you are considering going down this route.
|
Pasarell
regular
Reged: 18/01/2007
Posts: 195
Loc: Solent
|
|
Sensible advice from VicS to look at the International website. I think he meant hours between coats, not months though!
Gelshield 200 is solvent based so you won't want to put wet on tacky or it will blister. Wet on tacky only applies to the solvent free Gelshield
Good luck. A straightforward job if you follow the instructions
|
VicS
regular
Reged: 13/07/2002
Posts: 8369
Loc: Home: Kent. Boat: Chichester
|
|
Quote:
I think he meant hours between coats, not months though!
No at 15C minimum time between coats is 5 hours, maximum is 6mths. (Minimum varies with temperature.)
If you click the link you'll see!
--------------------
Old Chemists never die, they just fail to react
|
Pasarell
regular
Reged: 18/01/2007
Posts: 195
Loc: Solent
|
|
Sorry Vic. Misread your original post - far too late to be thinking straight!
|
Robih
regular
Reged: 29/11/2002
Posts: 1193
Loc: Hampshire
|
|
Just a note to encourage you - it's not a difficult process and we've been delighted with the quality of finish for application of the a/f. We're three seasons on from doing ours and adhesion is excellent. We were lucky and got all six coats on over an Easter weekend and were blessed with fine weather. By the time you've put two coats of a/f over the top so all together you're up to eight coats total you know the shape of your hull very well indeed!
rob
|
hughiain
regular
Reged: 13/07/2001
Posts: 96
Loc: kent
|
|
Most helpful - the marina has misled me into thinking I had to complete the task in 3 dry days. I now have the product information which seems fairly straightforward.
|
Previous
Index
Next
Threaded
Edit
Reply
Quote
