Roach1948
regular
Reged: 27/04/2006
Posts: 1015
Loc: London - Suffolk
|
|
I need to make some fiddle rails for a sideboard, the trouble is that they are quite small and I keep messing up using the corner round bit on the router – they are too small to clamp down and get a run on the router, so I have clamped the router to the bench and fed the wood in (wearing very thick gloves) – well I mess it up every time. The thing either bounces, or makes a gouge, or I ned up with a wavy contour. What is the way to contour these fiddly little rails? Is there a trick I am missing?
--------------------
Roach
|
Billy_Mizzen
regular
Reged: 05/01/2008
Posts: 31
Loc: East Coast
|
|
Perhaps a router table?
|
Cuchilo
regular
Reged: 19/04/2003
Posts: 4454
Loc: London
|
|
Clamp the fiddle beteen two points and support the router (fixed) above that . Then plunge down and turn the fiddle to make your cut .
Big version ......
sounds like a drill lathe made by wolf craft ? is just what you want , or i could knock them up for you unless you want thousands of them 
--------------------
Dont come running to me if you fall over and break your leg .
|
Peeriemaa
regular
Reged: 16/11/2005
Posts: 54
|
|
It seems to me that by the time you have set up the router etc, you could have finished the job, and derived more pleasure by using a sharp block plane, taking corners off just as you would round a spar. Absolutely guarantee keeping all of your finger tips as well.
Nick
|
Cuchilo
regular
Reged: 19/04/2003
Posts: 4454
Loc: London
|
|
I assumed that the round over was to be in the centre of the work and the ends would be fixed to a rail , making a fiddle rail .
--------------------
Dont come running to me if you fall over and break your leg .
|
Twisterowner
regular
Reged: 23/07/2005
Posts: 3764
Loc: ally poor
|
|
Start with a wider piece of timber so you have more support for the router, rout the edge, then saw it off.
Instead of clamps use double-sided sticky tape.
If you can get to Horsham, may I suggest attending one of Ron Fox's 1-day router courses? Good value and you learn a lot.
|
Roach1948
regular
Reged: 27/04/2006
Posts: 1015
Loc: London - Suffolk
|
|
Thanks chaps. I only have 3 to make so a router table is really OTT. I reckon I will go with Nicks suggestion and now that Roach is launched, I can do that aboard.
Twister - should have done that course a long time ago.....
--------------------
Roach
|
Cuchilo
regular
Reged: 19/04/2003
Posts: 4454
Loc: London
|
|
I must be missing something then ? I assumed you wanted to turn the fiddles for the fiddle rails 
Ron Fox is master of the router ..... ish
I have seen him a few times and my ex used to call him Ronnie the router  God i miss her , she used to crease me up 
--------------------
Dont come running to me if you fall over and break your leg .
|
meldrum
regular
Reged: 01/05/2008
Posts: 42
|
|
might I suggest making larger deeper fiddles they may not be quite so aesthetically pleasing, but they will be of much more practical use at sea. Small fiddles aren,t really a lot of use. also a block plane and sanding might be a better way as unless the router tool you are using is of a large enough radius ie half the thickness of the fiddle you will always have difficulty achieving a decent finish.
|
Roach1948
regular
Reged: 27/04/2006
Posts: 1015
Loc: London - Suffolk
|
|
Sorry Cuchilo, I mean fiddles alone and not rails - no wonder you got confused.
--------------------
Roach
|
Previous
Index
Next
Threaded
Edit
Reply
Quote
